Exterior

Silicone Lunateks Textured Exterior Coating

Name: Silicone Lunateks Textured Exterior Coating
Brand: Luna Tones

Sold by quote

Water-based, acrylic copolymer binder-based, silicone-reinforced, matt, grainy topcoat exterior cladding material, textured with a coral roller.

Coverage1–1.5 m²/kg

Full cure24 hours

Application temp.+5 °C to +30 °C

Packaging

25 kgOut of stock

Request a quote Contact

Colours

Rock Grey LT071 Ice Grey LT031 Desert Sand LT021 Pure White LT001 Marble White LT072 Mist Grey LT032 Straw LT022 Snow White LT002 Sand Beige LT073 Silver LT033 Clay Brown LT023 Pearl White LT003

See all 30 colours Try it on your wall

Technical documents:

Where to use

Used on all kinds of plastered surfaces (concrete, gas concrete, briquette, brick, mineral plaster, etc.).

How to apply

Clean the surfaces of all dirt, oil, loose and flaking layers, and of dust that may prevent the topcoat and primer from adhering, then prime them with Luna Tones Silicone Exterior Primer or Luna Tones Opaque Acrylic Primer. After the primer has dried, apply Lunateks Textured Exterior Coating in a single coat. It is ready to use. Spread the material evenly with a roller, then create the desired texture with a coral roller. Depending on the type, absorbency and structure of the surface, 1 kg of Lunateks Textured Exterior Coating covers approximately 1–1.5 m² (*). (*) Consumption may vary depending on texture thickness, surface, temperature and application conditions; the stated coverage rates are therefore for guidance only. A controlled sample application should be carried out to determine exact consumption.

Storage conditions

Store in a closed environment, in its original sealed packaging, between +5 °C and +35 °C for 12 months.

Important notice

Since factors such as application conditions, consumption amount, surface texture, air and surface temperature, thinning ratio and application thickness may vary, the consumption rates are given for recommendation purposes only. A controlled sample test should be carried out for precise consumption. Drying times may vary depending on the ambient and surface temperature, humidity levels and application thickness.

Shows excellent adhesion to all kinds of surfaces. It does not crack or peel. It has high alkali resistance. It is extremely resistant to sunlight, moisture and salty seawater on coastlines. Depending on the applicator's roller technique, a fine or thick pattern can be obtained. With its breathability, it helps moisture in the wall escape.

Water-based

Complies with the G Communiqué (manufacturer's declaration)

Coverage1–1.5 m²/kg

Full cure24 hours

Application temp.+5 °C to +30 °C

Base / formulation	Water-based, acrylic copolymer binder, silicone-modified
Gloss	Matt
Coverage	1–1.5 m²/kg
Colour	Variable
Pattern	Textured
Full cure	24 hours
Dilution Ratio	Ready to use
Surfaces	Concrete, aerated concrete, block, brick, mineral renders
Application temperature	+5 °C to +30 °C
Shelf life	12 months (unopened)
Safety	MSDS
G Communiqué	Manufacturer's declaration: complies with the G Communiqué

Coral roller

Clean the surface

Protect from frost

Stir before use

PDFProduct catalogueDownload PDF

Hazard Statements

H317: May cause an allergic skin reaction.

Precautionary Statements

P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
P103: Read label before use.
P261: Avoid breathing dust/fume/gas/mist/vapours/spray.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P362+P364: Take off contaminated clothing and wash it before reuse.
P333+P313: If skin irritation or rash occurs: Get medical advice/attention.
P321: Specific treatment (see label).
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.